Is Your Fender Blender Pro Seat Sliding Too Much?
This bulletin addresses issues with seat post sliding performance. A correctly functioning seat post should be easy to slide up and down with one hand. If there are positions where it gets stuck, please see the three sections below.
1. Check which bolt you have: Check if the anti-rotate bolt behind the seat post is a domed button-head type. We’ve found that this design of bolt can cause issues with sliding performance. Even if your seatpost is sliding fine, we’d like to send you the replacement.
Get a replacement: Contact us and we will send you a replacement that doesn’t scratch the seatpost slot. Contact info below.
2. Deal with existing scratches: Check for scratching and burrs around the groove on the back of the seat post. You may notice that the seat post gets stuck as it slides into the frame in specific areas where the seat post is heavily marked or scratched.
Fix: Requires a sanding tool such as emery board, file, or sandpaper. If you would like us to send you one, please contact us, info below.
- Remove the seat post from the bike. The hex key that comes with the bike will be needed to remove the anti rotate bolt.
- Sand around and in the groove to remove sharp edges and burrs. Avoid breathing the dust. For the best sliding performance, you must take the rough spots all the way down. If your seatpost is really chewed up and you would prefer a fresh start, contact us for a new post!
- Immediately clean up any dust with a wet paper towel and wash your hands after completing the process.
- Repeat sanding as necessary.
3. Chatter: Seat Post chatters when sliding down and needs precise manual guidance in order to slide; especially when the seat is extended to a higher number, like 9 or 10.
Fix: Lubricate the seat post with a silicone-based grease. If you would like us to send you some, please contact us, info below. How to apply the grease
- Raise the seat post all the way up and clamp in place
- Apply the lubricant onto the post near the top, middle, and bottom to form 3 rings, about the size of a rubber bands
- Spread the lubricant over the whole seat post with a small piece of paper towel, napkin or rag (approx the size of a credit card)
- Slide the seat all the way up and down five times
- Using a fresh paper towel, wipe off the excess lubricant
If these or other performance issues are happening to your Fender Blender Pro, please contact us for support: 1-(888) 354-2453 techsupport@rockthebike.com
Read MoreWhat Style Wheel Do I Have?
When ordering new wheel covers OR an Icycleta Ice Cream Bike Attachment it’s important for us to know what style wheel you have. Not sure how to tell? Let us help you find out.
“What wheel cover style is compatible with my wheel?”
Ordering new wheel covers? We need to know which wheel you have so we make sure to send you the compatible wheel cover. Take a look at your wheel hub and see which image below matches your wheel.
“Do I need a new wheel for my Icycleta attachment?”
Ordering the Icycleta Ice Cream Bike Attachment? If you have the new wheel style you can attach the Icycleta pulley on the same wheel without requiring anything additional. If you have the older wheel style we will send a whole new wheel to attach the Icycleta to the Pro.
Please let us know in the COMMENTS section when placing your order.
New style wheel :
Old Style wheel :
Read More
Rentable Pedal Powered Activities
You can green your event by renting our Pedal Power gear, reducing your carbon footprint and inspiring people at your event. Pedal Power gives your event attendees a unique experience that they will never forget. Check out all our great Pedal Powered activities for rent, and let’s start talking about your upcoming event.
Read MoreCrewed Recharge Bar
A Recharge Bar is a combination of a Recharge Station and a DJ Rig. It’s more than just a place to recharge phones; it’s downright groovy! It’s a place to relax, pedal, get your heart going, meet others, and send great music out to a larger space.
Conferences are all about the sharing of knowledge and connections between people. Lately, both of those things involve mobile technology. People share knowledge and connect to each other with the devices they hold in their hands, and those devices require power. At the Pedal Powered Recharge Bar, each bike has its 8 USB ports capable of charging up to 8 or more phones at once.
Read MoreWhat kind of vehicle should I use to transport the Pro frame?
Most hatchback style cars can usually fit at least one partially disassembled Pro frame inside. You’ll want to use a car with a large trunk; it’s even better if the back seats fold down to extend the trunk space.
A pickup truck can carry 2-4 fully built Pro frames in the bed. Most SUVs can carry a single Pro frame in the trunk with no disassembly. Smaller cars may probably require some small adjustments or disassembly such as lowering the handlebars, dropping the saddle, or removing the crossbar to fit in the trunk or back seat.
Most vehicles can fit 2 bike blenders with small adjustments or disassembly. We will provide the hex wrenches you’ll need to reassemble the bike again at your destination.
Any car will work if you’re using a regular bike rack.
Above: Tone transports a Fender Blender Pro on a sedan with a regular bike rack. Note the towel wrapped around the end of the crossbar to keep it from scratching the bumper.
A roof rack can help if you want to use a small car and don’t want to do any disassembly. Here’s a photo to show roof rack use and size comparison.
We encourage you to try bike towing with your rental bike. It’s fun, safe, practical and reduces the carbon footprint of your event, and there is no disassembly required! Any bicycle with a rear rack can tow the Fender Blender Pro. There is no extra rental charge for the trailer wheels and hitch, or you can purchase the Tow Kit to travel with your bike blender.
It’s official, the Dual sLEDgehammer is a thing.
Now you can host a competitive pedaling challenge at your event with this side-by-side competitive sLEDgehammer. It converts 100% of the riders’ muscle power to light and feels harder as more light stages turn on. The rider who sustains the highest Wattage level for 3 seconds and reaches the victory sequence first is the winner. We took it out to a party for the semiconductor industry last week and got dozens of people pedaling and competing, breathing and gritting their teeth in an evening-long series of heats to determine the strongest rider in the company.
Here’s a good view of the gear. The only thing out of view is the power-analyzing circuit that typically sits on a nearby table. The key elements shown are: 2 Generator Pros (bikes), 2 11′-tall sLEDgehammer light towers, cabling.
